Your shopping cart is empty!
Welcome visitor! You can Login or Create an account
Categories
Specials
-
$175.00$250.00
-
$175.00$250.00
-
$175.00$250.00
-
$175.00$250.00
Motion Control
Motion Control Systems
3 phase 1.2 degree stepping angle
573S15-L 3 phase stepper motor gear pulley, 1.3NM, 1.2 degreee 5.8A.
Holding toque of 0.9 N*m to 1.5 N*m (128 - 184 oz-in)
High precision
Smooth movement
Low motor heating
Low movement noise
Angle Accuracy
+5%(full step, no load)
Temperature Rise
80°C Max
Ambient Temperature
-10°C -- +50°C
Insulation Resistance
100MΩmin.500VDC
..
$69.00
Add to Wish ListWishlist
Add to CompareCompare
Stepper Motor, 200 Steps/Rev, 57×76mm, 4.5V, 2 A/Phase
High-torgue hybrid stepping motor has a 1.8 degree angle (200 steps/revolution. Each phase draws 2A at 4.5V, allowing for a holding torgue of 14kg-cm (190 oz-in).
Six color-coded wires terminated with bare leads that allow it to be controlled by both unipolar and bipolar stepper motor drivers.
Size: 56.4 mm square × 76 mm, not including the shaft (NEMA 23)
Weight: 1 kg (35 oz)
Shaft diameter: 6.35 mm (0.25″) “D”
Steps per revolution: 200
Current rating: 2&nb..
$75.00
Add to Wish ListWishlist
Add to CompareCompare
3 Phase Stepper Motor Pulley
Rated Current: 4.0 (A)
Rated Torque: 3.0 (NM)
Rated Power: 10 - 20 (W)
Rated Voltage: 24 - 48 (V)
Rated Speed: 50 (RPM)
..
$75.00
Add to Wish ListWishlist
Add to CompareCompare
The USB Dongle is used in conjunction with the LaserCut53 software and the laser machine motion controller. This dongle allows the software to be opened without any restrictions that are placed on the "demo" mode version. The software would be able to Open files, save projects, and communicate with the laser machine.
The Green USB Dongle is specially used to communicate with following motion controller models and may be compatible with others:
MPC-03 internal card motion controllers
MPC 6515 with firmware 4.1.0.9 and 4.0.0.15
The color of the USB Dongle is..
$80.00
Add to Wish ListWishlist
Add to CompareCompare
The USB Dongle is used in conjunction with the LaserCut53 software and the laser machine motion controller. This dongle allows the software to be opened without any restrictions that are placed on the "demo" mode version. The software would be able to Open files, save projects, and communicate with the laser machine.
The White USB Dongle works with the following motion controller models:
MPC-03 internal card motion controllers
MPC 6515 with firmware 4.1.2.0 and newer
MPC 6525 all firmwares
MPC 6535 all firmwares
MPC 6565 all firmwares
MPC..
$180.00
Add to Wish ListWishlist
Add to CompareCompare
The USB Dongle is used in conjunction with the LaserCut53 software and the laser machine motion controller. This dongle allows the software to be opened without any restrictions that are placed on the "demo" mode version. The software would be able to Open files, save projects, and communicate with the laser machine.
The White USB Dongle works with the following motion controller models:
MPC-03 internal card motion controllers
MPC 6515 with firmware 4.1.2.0 and newer
MPC 6525 all firmwares
MPC 6535 all firmwares
MPC 6565 all firmwares
MPC 6575 all f..
$95.00
Add to Wish ListWishlist
Add to CompareCompare