Chillers

Sort By:
Show:
Display: List Grid
CW-3000 Chiller
Fan-Radiator-Based Chiller CW-3000  ** Temperature Controller, Closed fluid loop, 8-Inch radiator fan, Fluid level gauge, flow sensor interlock ***  For pumping and cooling the water that flows through the laser tube. Uses the ambient air temperature to cool the water to the set threshold and cools the laser tube. This item is typically suggested for laser systems with 30, 40, or 60 watts. The dimensions are 10.5 wide x 19 long x 15 tall (including handles) inches. Available in 120 VAC version only.  ..
$350.00
CW-5000 Chiller (120VAC)
Freon Compressor-Based Chiller CW-5000  ** Temperature Controller, Closed fluid loop, Freon compressor, Dual 8-Inch radiator fans, Fluid level gauge, flow sensor interlock ***  For pumping and cooling the water that flows through the laser tube. Maintains a water temperature less than the set threshold to keep the laser tube cool. This item is typically included in laser systems with higher than 60 watts. The dimensions are 11.5 wide x 22.5 long x 19 tall (including handles) inches. Available in 230 and 120 VAC versions. Please be careful to select the proper 110VA..
$700.00
CW-5000 Chiller (220VAC)
Freon Compressor-Based Chiller CW-5000 ** Temperature Controller, Closed fluid loop, Freon compressor, Dual 8-Inch radiator fans, Fluid level gauge, flow sensor interlock ***  For pumping and cooling the water that flows through the laser tube. Maintains a water temperature less than the set threshold to keep the laser tube cool. This item is typically included in laser systems with higher than 60 watts. The dimensions are 11.5 wide x 22.5 long x 19 tall (including handles) inches. Available in 230 and 120 VAC versions. Please be careful to select the proper 110VAC or 2..
$700.00
CW-5200 Chiller
Freon Compressor-Based Chiller CW-5200 ** Temperature Controller, Closed fluid loop, Freon compressor, Dual 8-Inch radiator fans, Fluid level gauge, flow sensor interlock ***  For pumping and cooling the water that flows through the laser tube. Maintains a water temperature less than the set threshold to keep the laser tube cool. The dimensions are 11.5 wide x 22.5 long x 19 tall (including handles) inches. This model is only available in 230VAC. *Call to Order ..
$760.00
CW-6000 Chillers
Freon Compressor-Based Chiller CW-6000 ** Temperature Controller, Closed fluid loop, Freon compressor, Dual 8-Inch radiator fans, Fluid level gauge, flow sensor interlock ***      For pumping and cooling the water that flows through the laser tube. Maintains a water temperature less than the set threshold to keep the laser tube cool. The dimensions are WWWW wide x LLLL long x TTTTT tall (including handles) inches. This model is only available in 230VAC. Please call for available inventory.  *Pre Order ..
$1,200.00
CWLS Water Level Sensor
Replacement Water Level Sensor for CW series water chillers. Typically using a 5-24VDC signal.  Wire length: ~20cm The switch circuit is Normally Open with the float dropped below the sensor (water level is low).  When the water level is above the sensor, the float is pushed up and actuates the sensor. The switch circuit becomes closed.  ..
$22.00
CWP-24VDC Replacement Water Pump, 24VDC
This is a direct replacement water pump for S&A brand of CW series water chillers. This water pump matches the CW-3000 and CW-5000 models.  Rabbit Laser USA uses the chillers for pumping the cooling fluid (Distilled Water) that flows through the laser tube. 24VDC Brushless motor Over-Voltage protection Elevated stand (inlet port is 2.125 inches from base) Inlet port - 0.75 OD, 0.60 ID (inches) Outlet port - 0.40 OD, 0.275 ID (inches) Direct replacement water pump for CW-5000 and CW-3000 chillers ..
$35.00
CWPS-S24VDC, Replacement Power Supply, 24VDC
Replacement Power Supply for the CW series water chillers. Powers the 24VDC water pump.   Power Output: 90 watts.  Voltage Selections: 12, 15, 18, 19, 21, 24 VDC Input voltage: 110 or 220 VAC ..
$22.00